What principle and type of density meter is used?

First, the density meter is to use what principle

Density meter
The gravity of the object pulls the object toward the ground, but if the object is placed in liquid, a force called buoyancy will produce a force in the opposite direction. The buoyancy force is equal to the gravity of the liquid the object replaces, or the gravity of the drained water.
The densitometer floats or sinks according to changes in the balance of gravity and buoyancy. A well-functioning densitometer can only float, so the force pushing the buoyancy upwards is slightly larger than the force pulling it down.
Because the volume of the densitometer does not change, it has the same volume of boiling water*. However, it becomes heavier because it contains more water. When gravity is greater than buoyancy, the density meter sinks. The weight of the densitometer is less than the weight of the same volume of water, so the densitometer floats again. Densitometer readings are big, small and small. When it is immersed in different liquids, the volume does not change. The iron sand or lead particles at the bottom of the densitometer are used to maintain the balance!

Densitometer readings are larger and smaller because P = Ïgh. The deeper the density meter enters the liquid, the greater the pressure, so the densitometer readings are larger and smaller.

Second, the type of density meter

Common densitometers and hydrometers include float densitometers, static pressure densitometers, vibratory densimeters, and radioisotope densitometers.

Float Densitometer Its working principle is that the buoyant force of an object in a fluid is related to the fluid density, and the greater the fluid density, the greater the buoyancy. Static pressure density meter Its working principle is: a certain height of the static pressure of the liquid column and the density of the liquid can be used as the scale value of the specific gravity value. The simplest of these instruments is the visual measurement of a float glass pyrometer, referred to as a glass hydrometer. Membrane box is a commonly used pressure measuring element. The densitometer for directly measuring the static pressure of the sample liquid column is called a capsule static pressure densitometer. Another commonly used is a single-tube blow densitometer. Instead of directly measuring the liquid column pressure, it uses measured air pressure. The blow pipe is inserted into a certain depth below the liquid surface to be measured, and the compressed air continuously escapes from the bottom of the pipe through the blow pipe. At this point, the pressure of air inside the tube is equal to the pressure of the sample liquid column at that height, and the pressure value can be converted into density. Two famous Austrian scientists, Hans. Stabinger and Hans Leopord, discovered the measuring principle of the oscillating tube densitometer: when the object is excited and oscillated, its vibration frequency or amplitude is related to the quality of the object itself.

U type oscillation tube

If a U-shaped glass tube is filled with a volume of a liquid sample, the change in its vibration frequency or amplitude reflects the mass or density and specific gravity of a certain volume of sample liquid. The two scientists later designed the prototype and handed it to Mr. Urich Santner and his company Anton Paar to design the earliest digital liquid density meter in 1967. At present, fully automatic liquid density meters are based on the principle of U-shaped oscillating tubes.

The radioisotope densitometer instrument is provided with a radioisotope radiation source. Its radioactive radiation (such as gamma rays) is received by the radiation detector after passing through a certain thickness of the measured sample. The absorption of radiation by a certain thickness of the sample is related to the density of the sample, and the signal of the radiation detector is related to the absorption, thus reflecting the density of the sample.

Garbage Truck

Carriage Removable Garbage Collection Truck,

the full introduction of the German production of technology and design. Using CNHTC truck chassis, the hydraulic system, electrical and electronic control system, lubrication system and the main parts are domestic and imported famous brand. Good in appearance and performance. This type of garbage truck is mainly used for municipal solid waste (MSW), commercial waste, and are used for non-toxic, non corrosive and non industrial radioactive waste collection and transportation.

Can realize a main vehicle equipped with a plurality of garbage box, reduce the total cost of operation. Rapid completion of loading and unloading and automatic garbage compression cycle control. Use of lightweight container design, greatly reducing the weight of the vehicle itself. Vehicle bridge load-bearing by heavy truck 16 tons of bridge, a large tonnage, improves the carrying capacity. At the same time with compression of the cargo, by of garbage filling and compression, reduce the volume of garbage, so as to further enhance the rate of volume, improve work efficiency.

Container with guide roller, the HYVA18 tons pull arm, hydraulic system, ensure convenient to load and unload the garbage box, improve work efficiency. Standard after the roller support or rear axle support and improve the stability of vehicle in the soft road for loading and unloading;

SINOTRUK HOWO Compressed Garbage Collection Truck 15-16CBM

Compressed garbage truck, connecting the main compartment with a collection box, with the

most reasonable angle, blade type main launch board, has a special parabolic surface

optimal loading angle formed by compressed garbage collecting box filling mechanism of

30T above the rolling force, with 10T loading pressure in the pressure compartment, at

the same time, launched in 5T has always been to squeeze pressure, squeeze compressed

garbage, is conducive to the compressed garbage from the main carriage. Full volume

utilization rate can reach more than 97%.

The vehicle function is complete, easy to operate, garbage loading, the hydraulic drive

and electronic program controller control, accurate, reliable performance, performance

and reliable. The garbage filling body, can automatically continuous work, can also be

semi automatic one-way work, or manual operation, and return to the function.

The vehicle hydraulic drive, the maximum working pressure of 210bar, the system working

pressure 180bar, rolling force on a garbage collection box is 30 tons, by collecting box

into the main chamber when the loading capacity is 10 tons, the main launch plate on the

extrusion pressure of compressed garbage, keeping 5 tons of garbage unloading force

launched the 10 tons, the compression loading mechanism of each loading compression cycle

time is 25 seconds, the launch cycle time in shirk refuse, no more than 45 seconds.

Hook Loader Truck,Garbage Truck,Compressed Collection Truck,Compressed Garbage Truck

SINOMICC INTERNATIONAL , https://www.rockstartyre.com